Types of Hydraulic Fittings and How to Identify the One in Your Hand

A fitting can thread on smoothly, tighten down by feel, and still leak the moment the system comes up to pressure. That’s the trap with hydraulics, because several connections share the same thread and seal in completely different ways. This guide covers the types of hydraulic fittings you’ll run into on North Carolina plant and mobile equipment, how each one seals, how to identify them with basic tools, and which substitutions to avoid.

The Main Types of Hydraulic Fittings

The quickest way to sort fittings is by where they seal. Only tapered threads seal on the threads themselves. Straight-thread connections seal on a flare, an O-ring, or a washer, and the threads just hold the joint together.

TypeStandardThreadWhere it sealsCommon use
JIC 37° flareSAE J514Straight37° metal coneGeneral fluid power, mobile and industrial
ORFSSAE J1453StraightO-ring on a flat faceHigh pressure, high vibration
O-ring boss (ORB)SAE J1926StraightO-ring at the portPump, valve, and manifold ports
NPT / NPTFANSI B1.20TaperedThreadsOlder ports and low-pressure lines
BSPPISO 228StraightWasher or O-ringEuropean and imported equipment
BSPTISO 7TaperedThreadsEuropean and imported equipment
Metric 24° cone (DIN)ISO 8434-1Straight24° coneEuropean machine tools and equipment
SAE 45° flareSAE J512Straight45° coneLower-pressure and automotive lines

Parker’s Triple-Lok line is its 37° JIC tube fitting, and Seal-Lok is its ORFS line. Our Parker hose and fittings page covers what we carry, and our Parker hydraulic fittings buyer’s guide goes deeper on choosing within the Parker range.

How Do I Tell What Hydraulic Fitting I Have?

Check the sealing surface first, then the thread. Look for a cone, a flat face with an O-ring, or an O-ring at the base. Then measure the thread with calipers and a pitch gauge, and confirm any cone angle with a seat gauge.

Work through it in this order:

  1. Clean the fitting. Grime hides the seat, and it can also throw off your measurement.
  2. Look at the nose. A coned nose points to JIC, 45° flare, or metric cone. A flat face with an O-ring groove means ORFS.
  3. Check for taper. A tapered thread narrows toward the end, which points to NPT or BSPT.
  4. Measure the outside diameter of a male thread or the inside diameter of a female thread with calipers.
  5. Count the pitch with a thread gauge, then match it to a chart.
  6. Check the seat angle. This is what separates 37° from 45°.

If you don’t have a thread gauge, we keep them at our Sanford counter. Bring the fitting in.

Dash Sizes and the Threads That Fool People

A dash size is the nominal size in sixteenths of an inch, so a -8 is 8/16, or 1/2 inch. It doesn’t tell you the thread, because the thread changes by connection type:

DashJIC / ORB threadORFS thread
-47/16-209/16-18
-69/16-1811/16-16
-83/4-1613/16-16
-107/8-141-14
-121-1/16-121-3/16-12
-161-5/16-121-7/16-12
-201-5/8-121-11/16-12

Now look at the table closely. A -6 JIC and a -4 ORFS share a 9/16-18 thread, so they’ll thread together, but one seals on a cone and the other on a flat O-ring face. They won’t seal.

The same trap catches 37° and 45° flares, since some sizes share a thread while the seat angles differ. A fitting that threads on isn’t proof it’s the right fitting.

Pressure is a separate check. Ratings vary by type, size, and material, and they often fall as the fitting gets larger. Look up the exact part, and match the lowest-rated component in the line.

Not sure what you’re holding? Bring it to 111 McNeil Rd. in Sanford or call Cruco at (919) 777-9807. Our hydraulic specialists can identify the fitting and build the assembly.

Hose Fittings vs. Tube Fittings and Adapters

A hose fitting is crimped onto the hose and carries one of the end styles above. Parker’s 43 Series, for example, is a crimp fitting family with JIC, Seal-Lok, BSP, and metric ends. So “what series is it” and “what end is it” are two different questions, and you need both answers to order correctly. The hose has to be on Parker’s compatibility list for that fitting series too.

Tube fittings connect rigid lines, and adapters connect one thread type to another. Adapters are the normal fix when a port and a hose end don’t match, such as an ORB port on a pump feeding a JIC hose. Avoid stacking several adapters to solve one problem, since each one adds a leak point and more length for vibration to work on.

When you replace a hose, check the port fittings at both ends. Our guide to hydraulic hose replacement covers what to document before you pull the old line.

Where We See Each Fitting in NC Plants

Fitting mix usually tells you something about the machine. Domestic plant equipment and mobile machinery commonly use JIC and ORB, while newer equipment increasingly uses ORFS where vibration and leak control matter most. Imported machine tools bring BSP and metric connections. That’s common in the advanced manufacturing and pharmaceutical plants served by our Raleigh industrial supply customers around Research Triangle Park.

Agricultural and processing equipment around Smithfield often mixes generations on the same machine, so an older NPT port may sit beside a newer ORB connection. Before a holiday shutdown, walk your critical machines and record the fitting type and dash size at each hose end. That list turns a breakdown call into a same-visit fix.

Frequently Asked Questions

How do you tell if a fitting is JIC or SAE?
Check the seat angle with a seat gauge. A JIC fitting has a 37° flare, while an SAE flare fitting has a 45° flare. Some sizes share a thread, so the thread alone won’t settle it.

Are JIC and NPT threads the same?
No. JIC is a straight thread that seals on a 37° metal cone. NPT is a tapered thread that seals on the threads themselves. They won’t connect without an adapter.

Can you use Teflon tape on hydraulic fittings?
Not on JIC, ORFS, or ORB fittings, because their threads don’t make the seal. Tape can also shred and get into the fluid. On NPT threads, we prefer a liquid sealant made for hydraulic service.

What does JIC stand for in hydraulic fittings?
JIC stands for Joint Industry Council, the now-defunct group behind the original standard. Today, the 37° flare connection is defined by SAE J514.

What is the most leak-resistant hydraulic fitting?
O-ring face seal fittings are generally considered the best for leak control, because the elastomer O-ring seals against a flat face. That’s why they’re often chosen for high-pressure, high-vibration systems.

The Bottom Line

The types of hydraulic fittings make more sense once you sort them by how they seal. Identify the sealing surface, measure the thread, and confirm the angle, and don’t take a good thread engagement as proof of a match. Getting it right the first time avoids a second shutdown and a fluid cleanup. Keep a record of fitting type and dash size for your critical lines, and the next failure becomes a quick parts order.

Call Cruco Mill & Industrial Supply at (919) 777-9807 or bring the fitting to our Sanford counter. We work with plants across Raleigh, Smithfield, Durham, Greensboro, and central North Carolina.