V-Belt Size Chart and How to Read Any Belt Number
The drive is down, the old belt is in your hand, and the number on the back has worn off. Ordering by guesswork costs another day of downtime. This V-belt size chart covers the classical, narrow wedge, and light-duty sections you’ll see in a plant, how to read the number when you can see it, and how to measure the belt when you can’t. It also covers the mix-ups that send people back to the counter, including the 5/8-inch belts that look alike but don’t fit the same sheave.
V-Belt Size Chart by Cross Section
The section tells you the belt’s width and depth, and the belt must match the sheave groove. Measure across the top of the belt, then check the depth to confirm.
| Section | Family | Top width | Depth |
|---|---|---|---|
| A / AX | Classical | 1/2″ | 5/16″ |
| B / BX | Classical | 21/32″ (often listed as 5/8″) | 13/32″ |
| C / CX | Classical | 7/8″ | 17/32″ |
| D | Classical | 1-1/4″ | 3/4″ |
| E | Classical | 1-1/2″ | 1″ |
| 3V / 3VX | Narrow wedge | 3/8″ | 21/64″ |
| 5V / 5VX | Narrow wedge | 5/8″ | 35/64″ |
| 8V / 8VX | Narrow wedge | 1″ | 7/8″ |
| 3L | Light duty (FHP) | 3/8″ | 7/32″ |
| 4L | Light duty (FHP) | 1/2″ | 5/16″ |
| 5L | Light duty (FHP) | 21/32″ | 3/8″ |
An X means a cogged or notched belt. The notches help it bend around smaller sheaves and run cooler. Dimensions can vary slightly by manufacturer, so treat a close call as a reason to check the sheave.
How to Read V-Belt Numbers
The system depends on the belt family, and this is where most ordering errors start:
- Classical (A, B, C, D, E): The number is the inside length in inches. A B75 is a B-section belt with a 75-inch inside circumference.
- Cogged classical (AX, BX, CX): Same rule. A BX80 is a cogged B-section with an 80-inch inside length and replaces a B80.
- Narrow wedge (3V, 5V, 8V): The number is outside length times 10. A 5V1180 is 118 inches outside. The first digit is the top width in eighths of an inch, so 5V is 5/8 inch.
- Light duty (3L, 4L, 5L): Also outside length times 10. A 4L620 is 62 inches outside.
Classical sizes cross over between brands. An A68 from Gates, Continental, or Bando is the same physical size. We carry power transmission supplies including Gates belts and can cross most worn numbers at the counter.
How Do You Measure a V-Belt With No Number?
Measure the top width and depth to find the section, then wrap a flexible tape around the outside of the belt for the outside circumference. For classical belts, subtract the section’s factor to get the belt number. Narrow wedge and light-duty belts use the outside length directly.
Gates publishes these conversion factors for classical belts up to 210 inches:
| Section | Subtract from outside length |
|---|---|
| A | 2″ |
| B | 3″ |
| C | 4″ |
| D | 5″ |
| E | 7″ |
A worked example helps. A belt with a 1/2-inch top and a 70-inch outside length is an A68. A belt with a 21/32-inch top and a 71-inch outside length is a B68.
Keep in mind that a used belt has stretched and worn, so its measurement runs a little off. When a drive has an adjustable motor base, the size usually still lands within reach. If the measurement falls between sizes, check the sheave groove and the center distance before ordering.
Got a worn belt and no number? Bring it to 111 McNeil Rd. in Sanford or call Cruco at (919) 777-9807. Our power transmission experts can help identify the section and length.
Why Similar Belts Aren’t Interchangeable
Three mix-ups cause most of the repeat trips:
- 5V vs. B. Both are about 5/8 inch across the top, but the 5V is deeper with a different profile. It doesn’t belong in a B-section sheave.
- 4L vs. A, 5L vs. B. The widths match, but L-section belts are built for light-duty, fractional-horsepower service. They often won’t last on an industrial drive.
- Inside vs. outside length. A 4L680 and an A68 differ by more than their labels suggest, since one number is outside length and the other is inside length.
On multi-groove drives, replace the whole set together. A new belt running beside worn ones carries more than its share of the load and tends to fail early. If you’re deciding whether a belt is the right drive at all, our comparison of chain drive vs. belt drive walks through the tradeoffs, and our guide to types of bearings covers the shaft components worth checking while the guard is off.
Keeping Spare Belts on Hand in NC Plants
Belt drives run hard across central North Carolina, and the risk looks different by industry. Grain and feed operations around Smithfield and Johnston County have just come through peak harvest hours, so belts on elevators, conveyors, and hammer mills deserve a close look now. Textile and manufacturing plants in the Greensboro area often use holiday shutdowns for drive maintenance.
A simple shelf list prevents most belt emergencies. Record the belt number, drive location, and quantity per drive, then stock one full set for each critical machine. Write the number on the guard so nobody has to read a worn belt next time. It’s the same thinking behind a basic MRO inventory system. And when something unusual breaks, it’s worth a call. One Google reviewer came to us after searching online for a commercial compressor pulley that was back-ordered elsewhere, and was out the door in under 10 minutes.
Frequently Asked Questions
Are V-belts measured by inside or outside diameter?
It depends on the type. Classical A, B, C, D, and E belt numbers use inside length. Narrow wedge and light-duty belt numbers use outside length times 10. Measure the outside with a flexible tape, then convert if the belt is classical.
What is the difference between A and B V-belts?
Width and depth. An A-section belt is 1/2 inch wide and 5/16 inch deep, while a B-section is about 21/32 inch wide and 13/32 inch deep. They need different sheave grooves and aren’t interchangeable.
How do I know the size of a V-belt?
Read the number on the belt’s back. If it’s worn off, measure the top width and depth to find the section, then measure the outside length. For classical belts, subtract the section’s factor to get the size.
Can I replace a standard V-belt with a cogged one?
Generally yes, within the same section and length. A BX80 replaces a B80 and handles smaller sheaves better. Cogged and wrapped belts shouldn’t be mixed in the same matched set.
The Bottom Line
Start with the section, confirm whether the number means inside or outside length, and don’t let a matching width fool you into the wrong profile. This V-belt size chart will get most drives identified from the old belt alone. If the belt is gone or unreadable, the sheave groove and the drive’s center distance can still narrow it down, so bring those measurements with you. A belt number written on the guard makes the next replacement much faster.
Call Cruco Mill & Industrial Supply at (919) 777-9807 or bring your worn belt to our Sanford counter. We supply plants across Smithfield, Greensboro, Raleigh, Durham, and central North Carolina.