Hard Hat Types and Classes: What the Label Inside the Shell Means
Flip a hard hat over and you’ll find a short string of codes molded or printed inside it: a standard, a type, a class, and a date. Those codes decide whether the hat fits the hazards on your floor. Most hard hat types questions come down to two independent choices. The type covers where the hat handles impact, and the class covers electrical protection. This guide explains both, how to choose for your site, and when a hat that still looks fine needs to go.
Hard Hat Classes and Types at a Glance
ANSI/ISEA Z89.1 is the standard that sets these ratings. Type and class are separate, so a hat can be any combination, such as Type II, Class E.
| Rating | What it means | Good fit |
|---|---|---|
| Type I | Tested for impact to the top of the head | General plant work with overhead hazards |
| Type II | Tested for top and lateral impact, usually with a foam liner | Work around moving equipment and side-impact risks |
| Class G (General) | Proof-tested at 2,200 volts | General use and low-voltage exposure |
| Class E (Electrical) | Proof-tested at 20,000 volts | Work near energized conductors |
| Class C (Conductive) | No electrical protection | Sites with no electrical exposure |
Older hats may carry Class A or Class B. Under the current naming, those correspond to G and E. Vented hats are Class C, because the vent holes rule out an electrical rating.
Type 1 vs Type 2 Hard Hat: Which Do You Need?
A Type 1 hard hat is tested for blows to the top of the head, while a Type 2 is tested for blows to the top and sides. OSHA doesn’t universally require Type 2. Your hazard assessment decides, based on whether side impacts are realistic.
Think about what actually hits people on your floor. A dropped wrench from a mezzanine is a top-impact event. Walking into a pipe rack, getting clipped by a swinging load, or moving through tight machine bays involves side impact, and that’s where Type II earns its cost. It also matters that lateral hits can occur when someone falls.
Type II hats generally cost more and can run warmer. So some plants assign them by area or job rather than across the whole site. Whatever you pick, write down why. It’s a much easier conversation during an inspection.
What Does OSHA Require for Hard Hats?
Under 29 CFR 1910.135, employers must make sure affected employees wear a protective helmet where falling objects could injure the head, and an electrically protective helmet near exposed conductors that could contact the head. The head protection must meet a recognized ANSI Z89.1 edition or be shown equally effective.
The rule doesn’t pick a type or a class for you. It requires you to assess the hazard and match the hat, which is why the assessment comes first. Our overview of industrial safety gear requirements covers how that fits with the rest of your PPE program. North Carolina also runs its own OSHA-approved state program through the NC Department of Labor, so confirm any site-specific questions there.
A couple of details tend to be misunderstood. OSHA doesn’t set a hard hat color code. Colors are usually a company or site policy. A label may also show optional marks, such as LT for low temperature, HT for high temperature, or a reverse-donning symbol if the hat is rated to be worn backward.
Matching hats to a hazard assessment? Call Cruco at (919) 777-9807 or visit us in Sanford. Our industrial safety gear lineup includes hard hats, hearing protection, eye protection, and fall protection from names like Pyramex and MCR Safety.
How Long Are Hard Hats Good For?
Most manufacturers set the limits at about 12 months for the suspension and 5 years for the shell. MSA and Pyramex both publish that guidance. The date code inside shows when the hat was made, not when it expires. Check your manufacturer’s instructions, including when the clock starts.
Those numbers are maximums, not targets. Replace a hat sooner if any of these apply:
- It took a hit. Replace it after any significant impact or penetration, even with no visible damage.
- The shell has changed. Look for cracks, dents, gouges, chalky or faded plastic, or brittleness when you flex the brim.
- It lives in the sun or heat. UV and heat wear down plastic faster. Some makers advise a much shorter life for hats in direct sun, so outdoor crews should check their brand’s guidance.
- It’s been exposed to chemicals. Solvents, paints, and some adhesives can weaken a shell.
- The suspension is worn. Replace frayed, cracked, or stretched parts with the maker’s own suspension, since the shell and suspension are certified together.
Write the in-service date inside each new shell. Then a quick check before each use tells you where you stand. Keep the hat out of the rear window of a truck, where North Carolina summers can do real damage.
Matching Hard Hats to NC Worksites
The right hat changes with the work. Lab and pharmaceutical facilities around Durham and Research Triangle Park often have contractors moving through mechanical spaces, where a Type II hat handles low pipes and ductwork. Construction and advanced manufacturing sites covered by our Raleigh industrial supply team may need Class E near electrical work.
Feed and grain operations often see overhead hazards around elevators and conveyors. Steel and fabrication shops should also account for heat and sparks, and our guide to welding safety equipment covers what else belongs on those crews. If people work in tanks or vaults, add chin straps to your list and review our confined space safety equipment guide, since a hat that falls off during a retrieval doesn’t protect anyone.
A vented Class C hat is tempting in a humid Carolina July. It’s a fine choice on sites with no electrical exposure. Just don’t let it migrate to a job near energized equipment.
Frequently Asked Questions
What is the difference between Class G and Class E hard hats?
Class G hats are proof-tested at 2,200 volts and suit general use and low-voltage exposure. Class E hats are proof-tested at 20,000 volts for work near energized conductors. Both also provide impact protection for their type.
Are Type 2 hard hats required by OSHA?
Not universally. OSHA requires head protection that meets the ANSI standard and fits the hazard, but doesn’t mandate Type 2 across the board. If your assessment shows side-impact risk, Type 2 is the better match.
What is a Type 1, Class G hard hat?
It’s a hat tested for impact to the top of the head and proof-tested at 2,200 volts. It’s a common choice for general industrial work with overhead hazards and low electrical risk.
Does a hard hat expire?
There’s no single legal expiration date. Manufacturers set the service life, often up to 5 years for the shell and 12 months for the suspension. Replace it right away after a significant impact or if you see damage.
The Bottom Line
Hard hat types and classes answer two separate questions: where the impact may come from, and whether electricity is in play. Start with your hazard assessment, choose the combination it calls for, and track the dates so hats leave service on time. A simple log of issue dates and a yearly suspension swap keeps the whole crew inside the manufacturer’s limits without much effort.
Call Cruco Mill & Industrial Supply at (919) 777-9807 to outfit a crew or restock suspensions. We supply plants across Durham, Raleigh, Greensboro, Smithfield, and central North Carolina from our Sanford location.